Differences

This shows you the differences between two versions of the page.

--- setup:setup_preferences [2019/01/30 09:29] – Jan_K
+++ setup:setup_preferences [2022/02/11 07:23] (current) – old revision restored (2019/02/08 19:38) Jan_K
@@ Line 89: / Line 89: @@
 === Password. ===
 The Password protection is used to protect the access to the Freestyler Setup.\\
-“Setup” is removed from the menu bar.\\
+\\
-All other function will still be access able.\\
+**This will remove “Setup” from the menu bar.**\\
+All other function can additionally be blocked so only a limited functions / panels are accessable.\\
 \\
 {{:images:setup_menu:setup_preferences_password.jpg|}}\\
@@ Line 98: / Line 99: @@
 The Password window has check boxes in the right side where it is possible select which areas to protect with the Password.\\
 If it is a password change then the old password are to be entered additionally.\\
-To delete the password leave the new password box empty.\\
+**To delete the password leave the new password box empty.**\\
 It can be necessary to close the program to deactivate the password protection.\\
+\\
+And the "Setup" menu's are gone.\\
+{{:setup:setup_preferences_password_02.jpg?|}}\\
 \\
 To unlock the ”Setup” goto the file menu and select “Enter password and disable security”.\\
 \\
-{{:images:setup_menu:setup_preferences_fs_password.gif|}}\\
+{{:setup:setup_preferences_password_01.jpg?|}}\\
 \\
 The ”Enter Password” popup will appear.\\
 \\
-{{:images:setup_menu:setup_preferences_fs_password_01.gif|}}\\
+{{:setup:setup_preferences_password_03.jpg?|}}\\
 \\
 If the Password protection are to be enabled again then it is done by setting up the password again.
@@ Line 113: / Line 117: @@
 \\
 \\
-== Pan / Tilt resize.==
+-----
+=== Pan / Tilt resize.===
 Sometimes when you preprogrammed sequences for a special location and you might want to use the same sequences on another location then you are able to resize the pan & tilt movements (going from 1 to 120%).\\
 \\
@@ Line 119: / Line 124: @@
 Note: Direct copy from help file.\\
 \\
-{{:images:setup_menu:setup_preferences_pantilt_resize.gif|}}\\
+{{:setup:setup_preference_pan_tilt_resize.jpg?|}}\\
 \\
 This is a general resizing that will affect all cues with movement control.\\
@@ Line 126: / Line 131: @@
 \\
 \\
-== Patch ==
+-----
+=== Patch ===
 Patch is a simple but effective way to place the same control on more channels.\\
-Her the Pan channel 11 is patched to Pan channel 25.\\
+Her the Amber channel 4 is patched to Amber channel 20, 36 and 52.\\
-This means that the vale from channel 25 also is set on channel 11 and the original control to this channel is omitted.\\
+This means that the vale from channel 4 also is send on the 3 patched channels and the original control to this channels is omitted.\\
 \\
-{{:images:setup_menu:setup_preferences_patch.gif|}}\\
+{{:setup:setup_preference_patch.jpg?|}}\\
 \\
 The patching is not active before it has been saved.\\
@@ Line 138: / Line 144: @@
 \\
 The patched channel are marked with red in the “Output”->”Show Output” window.\\
-Her channel 25s value 92 is also send on channel 11\\
+Her channel 4's value 98 is also send on channel 20, 36 and 52\\
 \\
-{{:images:setup_menu:sutup_preferences_patch_output.gif|}}\\
+{{:setup:setup_preference_patch_output.jpg?|}}\\
 \\
+So here the amber control for fixture 1 also controlles amber for the 3 other fixtures.\\
+An other example could be patching all channels for one fixture, one by one, to all fixtures of then same type.\\
+This gives that the fixture 1 will control all the fixtures.\\
+It will be the same as giving all the fixtures, the same DMX address to listen at in parallel.\\
+You gain that only one fixture control all fixtures, the lose is that you don't have individual control on the fixtures.\\
 \\
 \\
-== Zone. ==
+\\
+-----
+=== Zone. ===
 Zone can be used to group fixtures into tabs.\\
 This can be useful when there are some secondary lights to control.\\
 It will be possible to have a clean workspace where only fixtures that are related are placed.\\
 \\
-Note. Zones are not more DMX universes. It is still only one 512 channel universe.\\
+Note. Zones are not DMX universes. FreeStyler is 2x 512 channel (2 universes) and the fixtures can be organized on 4 tab's / zones.\\
 \\
-{{:images:setup_menu:setup_preferences_zone_tab.gif|}}\\
+{{:setup:setup_preference_zones_tabs.jpg?|}}\\
 \\
 The setup of each zone / tab are simply a name with max 10 char.\\
@@ Line 164: / Line 177: @@
 The background images has to fit the monitor in advance because it is not possible to size or center it in this setup.\\
 \\
-{{:images:setup_menu:setup_preferences_zones.gif|}}\\
+{{:setup:setup_preference_zones.jpg?|}}\\
 \\
 Here 4 Zones are defined Main rig, Dancefloor, Bar and hall.\\
@@ Line 174: / Line 187: @@
 When zone is enabled the Add fixture gets an extra field to select which zone the fixtuer are to be placed in.\\
 \\
-{{:images:setup_menu:setup_preferences_zone_add_fixture.gif|}}\\
+{{:setup:setup_preference_zones_add_fixtures.jpg?|}}\\
 \\
 \\
 And the same for the right click on the fixture. It also gets a "move to zone" control.\\
 \\
-{{:images:setup_menu:setup_preferences_zone_menu.gif|}}\\
+{{:setup:setup_preference_zones_popup_menu.jpg?|}}\\
+\\
+An example on Zones can be like the images bellow.\\
+\\
+{{:setup:setup_preference_zones_main_rig.jpg?|}}\\
+\\
+{{:setup:setup_preference_zones_dancefloor.jpg?|}}\\
 \\
 \\