Support Forum

I am new to using Freestyler and I am trying to start it to use in my shows ...

But I have the following problem: I select a moving head, I open the shutter, and increase the intensity to the max, but I do not see the beam in the Easy Viewer.

However, if use the sealing effect (strobe), the beam appears in the Viewer Easy ... I can only see the shows where I use strobe in moving heads!

The rest of the features (pan, tilt, etc) seem to work properly.

I use:

Windows 7 64bit Professional
Freestyler 3.4.8
Magic 3D easy view 2012.5.21.3054

I hope you can help!

Thank you, greetings.

hi
easyview isnt a Software from freestyler, freestyler just use this software.
so normaly i cant anwser you qaustions, only i had the same issue and know how to solve this.


Download the letest Beta version from Nicolaudia.
and Copy the new .EXE from the Beta to the old .EXE freestyler uses and everything willl work better then before.

/spirit

Hi Folks,

Before I ask the question I am about to, I can assure you I have searched high and low on the internet for a fix to this problem but no joy as yet.

I have attached 4 pars to FS and the same on EV. Both the output on FS and DMX level on EV show the values changing as I change the colours. Unfortunately I cannot get a beam on EV. I downloaded the latest version of EV dated Aug 02. My question is I do not understand copying the new .EXE file and replacing the old one. Could you please be a little more specific.
Thanks in advance for anyone who can help me please. Been on this for hours.

oke

if you install freestyler it also ask if you like to install 3Dview.
this is realy importent because the 3d view you install with freestyler will only work with freestyler.
if you install 3dview seperate from freestyler, then 3d View will not work!

so Install the lastest beta from the Nicolaudia webpage as you allready did.
Now Copy the New (Beta) Easyview.exe file To the Freestyler directory so you replace the old easyview.exe with the latest easyview.exe file.

now start FS and open easyview. and it should work ok.

so in steps.
1) Install Freestyler with Easyview.
2) install the Latest easyview beta from the nicoladia page.
3) By default go to C:/SLMEV Beta and copy the Easyview.exe file
4) by default go to C:/Freestyler and Past the file there.
5) start freestyler and open Easyview and it should be working.

/spirit

Hi, Thanks very much for coming back to me so quickly.... much appreciated. I apologise for not being too knowledgeable about all this however when I go into SLMV Beta I cannot find or recognise the .EXE file. Can you give me an idea of what it looks like please....??

here

OK thanks. I didnt see any .exe at the end of mine. I will give it a try now.

Great...... got them working now. Thanks for all your help !!!!!

I've done this but I now have an issue that the colours don;t show up properly on some led parcans

hi DJsupport

no issue with me..
Which ledcan do you use..
Here a little movie i made before..

https://www.dropbox.com/s/5ajt7nxq018wo ... 0031.mp4?m

/spirit

Alkalite octopod 30

Hi guys

I have the same problem with some fixtures not working correctly in EasyView.
I did the BETA-update but now I can not get the EasyView to react at all, there is no DMX-signals coming in.
If I replace the .EXE with the old one it works again.

Any ideas what could be wrong ?
One potential difference could be that the BETA is never than the one You have used.

You copy the beta exe to your fs folder once beta installed, and run it by clicking the icon within FS, i got my fixture to work after the other issues by simply opening the file in the scan library editor and then re-saving the file with a 'b' on the end and now it works fine!

Yes, that is what I did but it does not react to FS at all. I can start EasyView from the button but it does not take any signals from FS, and it won't stop from the same button.
If I copy the original easyview.exe back it works again.

Try it with virtual interface selected in the fs interface setup

I found an easyview.exe dated 27.7.2012 and now it works !
So beware, the easyview Beta You can download right now is not working (at least not for me) with FS

MagicJohansson wrote:I found an easyview.exe dated 27.7.2012 and now it works !
So beware, the easyview Beta You can download right now is not working (at least not for me) with FS

Where did you find the older version easyview.exe dated 27.7.2012 ?

Searching like crazy for hours!

тоже сейчас пытаюсь с этим разобраться, Robe colorspot 575at mode 3 как я понял разные установки по каналам в 3д маджик и в FS. наверное придется вручную перестроить библиотеку своих приборов под 3D magic или есть программа для импорта настроек приборов с FS to 3Dmagic view ????????????????????????

Если вы хотите приспособление для 3D-вид, то вам нужно создать один, как фристайлер и 3D-вид совершенно разные программы, а не управляют те же самые люди. Если вам нужна помощь, то дайте мне знать, и я посмотрю, что я могу сделать.

djSupport wrote:

What's a matter with you?

Your multilingual skills impress me!

hey ik kan ook in andere talen typen hoor!!!

djSupport wrote:Your multilingual skills impress me!

Oh right lol

A tøvs i har a' sjov houe.