Support Forum

hello,

i think i've nearly got the fixture right, i'm just not too sure about what i need to put in for the the strobe/shutter settings so i'm hoping someone can see where I've gone wrong? at the moment i have no control of light and it just flashes between colours itself.

i've uploaded my draft of the fixture file which can be found here...
http://www.thebrickyardonline.com/freestyler

and the user manual containing all of the DMX info can be downloaded here...
http://www.chauvetlighting.com/products ... ug-124.pdf

if someone could take a few minutes to point me in the right direction it would be greatly appreciated

thanks in advance
m

Hi,

you don't have to do this work.
There's a fixture already available here.

hi dustin

for some reason this fixture is not working for me.

i downloaded the .pff file and double clicked it, an error message popped up saying 'input past end of file'. the info for the light shows up in fixture creator but when i add it in freestyler, the intensity dosen't work, the strobe dosen't work and it won't go the colour i want it to be

this file has been downloaded 25 times or so and nobody has reported an error s could it be something at my end?

hello again onge

i tried out the fixture file today and it's not working sorry.

i was previously using the 'Chauvet LED Splash Jr.' fixture and this allowed me to control the colours but the intensity and strobe did not work properly.

here's where i'm at so far...
i installed your fixture profile, deleted the Splash Jr's, added the 200B's and set the addresses in freestyler. the 200B's are now taking up an extra channel. going from 83 - 100 to 83 - 101 (i can't remember the exact start address sorry). i changed the pins/addresses on the back on the lights to what Freestyler said they should be and still nothing works, not the colour, intensity, or strobe.

do you think it's a problem with the fixture file or something with the actual DMX addresses i have assigned?

hope you can help
thanks
m

Hey guys,

I created the fixture file and it still works perfect for me using 3.2. I have not upraded to 3.28 yet, but will do so next week when I get back home to make sure all is ok in that version.

i changed the pins/addresses on the back on the lights to what Freestyler said they should be and still nothing works, not the colour, intensity, or strobe.

Try swapping the dip switches around. A while back I re-addressed my whole rig. I took a quick glance at what Freestyler said the dip switches should be and nothing worked. It's the way you interpet what should be on = up or off = down (I forgot). Try going back to the original fixture file and swapping the switches on the light. Just a hunch that this may be the problem.

Let us know how it goes.

Shannon

Shannon is right.. I have been confused many times because I have misunderstood the illustration of the dipswtiches in freestyler. It is the black rectangles which is the switch. i always think it is the white ones, but they are the "gaps"

Exactly, I thought the white ones were the switches. All the fixtures I have seen that had dip switches have a red box with white switches. Maybe the colors can be changed in the next rev. This is probably the easiest thing for Raph to change Or make a note about it in the help file.

Shannon D wrote:Exactly, I thought the white ones were the switches. All the fixtures I have seen that had dip switches have a red box with white switches. Maybe the colors can be changed in the next rev. This is probably the easiest thing for Raph to change Or make a note about it in the help file.

yes. when you have white dip switches on fixtures it is logic that the dips in FS have the same colour.

so we agree that it could be great with following changes:

Blue dip switch box --> Red
Black dip switches --> White
White gaps --> black

The only problem is that there will be some users who are used to the current illustration and will get some issues in the beginning

so it seems the dip switches had to be the reverse of what Freestyler was telling me. however on some of my other lights the dip switches ARE as freestyler was telling me to set them as and they work fine.

the fixture file...
there's a couple of tweeks i havn't been able to get right after much playing about in fixture creator as i'm still not getting my head around the strobe, shutter and intensity settings sorry. i took a screen shot of the current settings so i can compare them with the amended file should anybody be able to make these adjustments? hopefully then i can see where i'm going wrong

at the moment the intensity is controlling the strobe and the strobe controlling the intensity. using the strobe to control the intensity, 100% turns the light off and 0% is the light at full brightness.

also when i click 'closed' the light just stays open and static with the colour selected from the pallette

thanks for all the help so far, much appreciated

m

newbie84 wrote:so it seems the dip switches had to be the reverse of what Freestyler was telling me. however on some of my other lights the dip switches ARE as freestyler was telling me to set them as and they work fine.

that sounds odd. Are you absolutely sure about this??? notice that it is the black rectangles in Freestyler illustration which the white dip switches on your lamp

hi onge

you could be on to something here. i've been going off the manual included in the box when i bought the lights but the light itself might be a different model to what was in the box (manufacturer's mistake) or they sent us the wrong manual for the lights?

i'll check the lights tomorrow as well as your other suggestion and keep you posted

many thanks
m

If the light is not what you paid for then you have two options:

1. if it is lesser of a light than what you paid for, return it and get the right one or your money back.

2. if it is a better light than what you paid for, then +1 for you and keep it. Get the right manual and we will help you get it going.

Atleast we know we got somewhere with the addressing and the light works.

hi folks

the fixtures are definitely chauvet LEDsplash 200B, or that's what the stickers say on them at least. i bought them ages ago and it's only now i'm getting familiar with freestyler so i will be unable to take them back

i've changed the strobe channel to 5 and intensity to 6 so at least i can control the lights to a degree

remaining problems...
when you click open it makes the strobe 100%

closed does nothing

the intensity; 100% = off and 0% = full.
i changed the 'min' to 255 and 'max' to 0 but then i cannot control the light at all

and the blackout works on all lights except these LED's

surely all 8 lights can't be faulty? anybody got any suggestions?



thanks
m

Here are print screens of my 200B set up.

If you not have any values for the shutter, it will work on the same channel as strobe

I notice you have intensity set at 255 min an 0 for max ? Is that how it works as it is not clear in the manual just gives a range of 0-255.

When I pulled up the file, I questioned that myself. But yes, that's correct. It just looks odd. Channel 6 is a dimmer channel for that light. So at 0, it is full intensity. The more you increase channel 6, the light dims. 255 turns the light off.

LJ_krede.dk wrote:If you not have any values for the shutter, it will work on the same channel as strobe


set shutter ch to 6,
close to 0
open to 255

then it shouldnt strobe when pressing the open button

That won't work with this light, as described in my earlier post. Channel 6 is a dimmer channel. If set like you mentioned, the light would turn off when the open button is pressed.

The way I use the light, I don't open or close the shutter, it's not programmed that way. I mainly use my macros or the sliders when programming or running the lights on the fly. For a black out of that light (or shutter close), I have a macro. For strobing, I have macros set at the interval that I liked. My personal preference is to only open the macro window and have all the control I want without opening all the other windows. For my global Black Out, I created a single step sequence with all my lights blacked out and saved it to my Favorite button. I don't use the black out button on the tool bar for nothing. It works for me.

Shannon D wrote:

LJ_krede.dk wrote:f you not have any values for the shutter, it will work on the same channel as strobe

set shutter ch to 6,
close to 0
open to 255

then it shouldnt strobe when pressing the open button

That won't work with this light, as described in my earlier post. Channel 6 is a dimmer channel. If set like you mentioned, the light would turn off when the open button is pressed.

Yes, I know that now, after Onge and you mentioned the dimmer channel was inverse. Then you just swap the values:
Close: 255
Open: 0

Shannon D wrote: The way I use the light, I don't open or close the shutter, it's not programmed that way. I mainly use my macros or the sliders when programming or running the lights on the fly. For a black out of that light (or shutter close), I have a macro. For strobing, I have macros set at the interval that I liked. My personal preference is to only open the macro window and have all the control I want without opening all the other windows. For my global Black Out, I created a single step sequence with all my lights blacked out and saved it to my Favorite button. I don't use the black out button on the tool bar for nothing. It works for me.

Fair enough
this is another reason to make all your fixture files yourself. you can customize your fixture files so they work as you prefer and for your purpose. maybe other people wants it differently

but if you want to use the global blackout button you have to define the close value for shutter in the fixture file. for fixture without a shutter(channel) you just define the shutter to the same channel as dimmer and the blackout would work.

I created that fixture file back in 2008. Yep, there are more than one way to skin a cat That's what cool about the fixture creator. Your the boss and you make the light work for you the way you want it to.

Ok Newbie84 (M), we need an update. Did you get that thing going yet?

hi folks

i won't be able to test the fixture file for a day or two but once i have i'll let you know how i get on

thanks for all the help
m