These adverts are supporting the forum's costs and the products/services are not endorsed by the forum owners.
First have you tried?
Log in to Search the Forum for help!
Learn more about using FreeStyler at the FreeStyler WIKI HERE
Learn more about DMX in General at The DMX Wiki HERE

if all else fails and you need a fixture consider the fixture building service HERE

MIDI control with BCF-2000

Questions regarding the Behringer BCF2000 controller.
Post Reply
Jaykie
Can now teach FS to others (Hopefully!)
Posts: 91
Joined: July 10th, 2007, 4:31 pm
FreeStyler Version: 3.01
Twitter: http://twitter.com/jaykie

MIDI control with BCF-2000

Post by Jaykie »

This is from the old forum
rrr
Hi all,

I recently purchased a BCF-2000 for use with Freestyler however I'm having trouble using the toggle buttons to select groups. The BCF-2000 has 16 toggle buttons with LED's that show current state (on/off). I want to have the buttons mapped to the Group select functions in freestyler ie. the first 10 buttons to the 10groups.

In normal operation the buttons send a certain note (or CC) with a value of 127 when toggled on, and the same note with value 0 when toggled off.

The first button press works fine (selects the right group), however to de-select the group you have to hit the button twice (goes to note/value0 then actually deselects the group in freestyler on the second press which sends note/value127).

Apart from being a bit of a pain this also gets the status LED's out of sync. ala, the LEDs on the controller don't correspond with the groups selected.

I have tried programming the BCF-2000 to change the on and off messages to both be 127 however it appears that the second 127 isn't sent (MIDI only sends changes???? not sure on that)

I have tried programming the BCF-2000 to send a on of value 127 and an off of 126, which almost works however I can't select and deselect the same group in a row. Ala, I can select group1 with button one, but I need send any other midi message before I can deselect group one (can be absolutely any midi message, not necessarily another group select).

I can use the trigger mode on the BCF for the buttons (where it sends a message for only as long as the button is held down), however this doesn't maintain the state of the LED. Ala, the selected groups in freestyler won't correspond to the LED's on the controller.


Any suggestions or help muchly appreciated.


PS. great program, thanks!

PPS. I had the same problem with a CME Bitstream I tested (that had "soft" LED's.

Mattotone
On the BCF edit the button in question, select mode (6th rottary dial button) and change value to t-Off this should fix your problem

rrr
I did try putting the buttons into toggle-off mode however that disables the LED (it sends a quick value 127 followed by value 0 so it's always "off" at the controller). It selects the group ok in freestyler but you lose the advantage of having toggle switches with LED's on the controller.

The reason I would like to have the LED's indicate what group i have selected is that I'm mixing using Traktor at the same time so I have Freestyler minimized. It's also the same functionality as a "traditional" lighting desk where you can see on the controller what you have selected.

Apart from an config option in Freestyler to ignore the value of the midi message, I can't think of another way of getting controllers with LED's to work with freestyler. Any other suggestions greatly appreciated.

Mattotone
It shouldn't disable the led,
Have you set freestyler up to send data back to the bcf?
Do the faders move if you change a value in freestyler?
Which version of freestyler are you running?
are you running the bcf in usb or Midi.

Kind regards

rrr
I have set MIDI out to be the BCF-2000 (using device BCF-2000[1] which is the same as input) but no, haven't had feedback working yet.

Am running freestyler 2.95h

And it's running in USB mode.


Thanks for your help

Mattotone
Thats really strange that no feedback is been shown, Maybe you could try reinstall the drivers for the bcf?

rrr
Just tried re-installing the drivers (am using version 1.2.1.3) however have the same problem. I have tried modes U-1 and U-3 and also setting a global RX channel of 1 (it was off by default). Any other suggestions?

Thanks

Mattotone
im not sure about those settings, iv never had to change mine.
my settings are as follows. from left to right. u-3, off, auto, last, id1.
i have it set in BC Mode, when the unit is off hold down the top left button (not rotary dial) and switch the unit on it should then display BC.
You may also want to update your device firmware from the behringer website.

regards


rastalulu14
Knows how to turn Lights ON
Posts: 1
Joined: March 22nd, 2018, 7:10 pm
FreeStyler Version: 3.6.4
I Use FreeStyler for: Stage Show

Re: MIDI control with BCF-2000

Post by rastalulu14 »

Hi, exactly the same problem here. Have you resolv it and how ?

regards
Partyman
FS is my life
Posts: 787
Joined: July 11th, 2007, 8:39 pm
FreeStyler Version: 4.01
I Use FreeStyler for: Nightclub Lighting
Twitter: twitter.com/
Contact:

Re: MIDI control with BCF-2000

Post by Partyman »

I am beginning to think its a version 4... bug. i will install an older version and see if it gets feedback
Partyman
FS is my life
Posts: 787
Joined: July 11th, 2007, 8:39 pm
FreeStyler Version: 4.01
I Use FreeStyler for: Nightclub Lighting
Twitter: twitter.com/
Contact:

Re: MIDI control with BCF-2000

Post by Partyman »

It is not a Freestyler issue, it must be something that happened in a windows update. the unit does not respond using audio control software either.
User avatar
djSupport
Hosts the Freestyler Forum and is an Admin!
Posts: 1908
Joined: July 9th, 2007, 6:57 pm
FreeStyler Version: Forum la
I Use FreeStyler for: Just for the Fun of it.
Contact:

Re: MIDI control with BCF-2000

Post by djSupport »

If it's a Windows issue it 'may' need changing at FreeStylers end. You should file a bug report with your findings
Heather Trott, You Babe! I Drive a Dacia Duster and Explore! Check it out
Post Reply

Return to “BCF2000”